Thermostat temperature and sensing
HVAC Engineer · Certified HVAC Specialist · Manager at DENAIR, Dubai
Check which temperature the screen is showing
If your thermostat says 24°C while a separate thermometer says 26°C, start by identifying both numbers. The setpoint is the temperature you have requested. The room-temperature display is a measured value. Depending on the controller and its configuration, the normal screen may show one or the other.
Photograph the display with its labels and symbols visible, and check the user guide for your exact model. Confirm that both devices use the same units. A difference between the setpoint and the measured room temperature does not establish a sensor fault.

A wall controller documented during a DENAIR service visit.
Find out where the temperature is being sensed
The wall controller is not always the source of the temperature reading. Some systems can use a sensor at the indoor unit instead. As a model-specific example, the Daikin BRC1E53 user guide describes selecting between the remote-controller and indoor-unit temperature sensors. This does not identify the arrangement in your home.
Ask the technician which sensor supplies the displayed temperature and which sensor controls cooling. Changing an offset before answering those questions can leave the underlying mismatch unexplained.
On a DENAIR service visit, the team changed temperature sensing from the indoor unit to the wall thermostat as part of a wider software and settings review. Checking which sensor is active is a useful step before considering calibration.
Make the comparison useful
For an initial check of a wall-mounted sensor, place a suitable room thermometer nearby at a similar height, without covering or touching the controller. Allow readings to settle according to the device instructions. Comparing a thermometer beside a cold-air outlet with a thermostat across the room mixes measurement location with possible sensor error.
Keep a short record during normal use:
The thermostat's room reading, selected setpoint and operating mode.
The separate thermometer reading, its position and the time.
Whether the difference stays similar or changes through the day.
Recent installation, servicing, setting changes or power interruptions.
If the active sensor is inside inaccessible equipment, let the technician arrange the comparison. You do not need to open a controller or ceiling unit.
Look for local heat and draughts
A sensor may be responding to conditions around it that do not represent where you sit or sleep. Notice direct sunlight, nearby heat-producing equipment, a frequently opened door or air blowing towards the controller.
For the BRC1E53, Daikin's installation guidance calls for a location that represents the room temperature, away from sunlight, heat sources and outside-air draughts. Photograph the surroundings for your technician. Leave relocation and work behind the controller to a qualified installer.
Consider calibration after the source and conditions are checked
Some thermostats permit a temperature correction, but the available range and procedure depend on the model. The Siemens RDF302-family operating instructions, for example, specify at least one hour of operation before comparing temperatures for recalibration and list an adjustment range of −3°C to +3°C. Those limits are not instructions for other thermostats.
Ask whether an adjustment is appropriate for the selected sensor and measured difference. A fixed correction should not be used to hide a changing placement problem. Have the technician record any change and check the reading and cooling response afterwards. Avoid installer-menu experiments or repeated resets, which can alter other settings.
When reconfiguration may be enough
A thermostat that behaves unexpectedly does not automatically need replacing. Ask the technician to separate a supported setting that is wrong for the installation from a failed component or a function the controller cannot provide. Reconfiguration means correcting a documented setting on equipment that supports the intended job.
For example, the Daikin BRC1E53 installer guide describes sensor-related field settings and notes that unavailable functions are not displayed for the connected indoor units. The technician must check the paired equipment and its documentation; a setting available on one installation may not exist on another.
A supported setting is incorrect: if the technician confirms that the selected sensing source, display option or other relevant setting does not match the intended arrangement, ask for the current setting, proposed correction and reason to be recorded. A model-supported change may be sufficient, but the original temperature comparison and actual cooling response still need to be checked afterwards.
A fault or compatibility limit is demonstrated: ask which test identifies the affected component, or which required function the installed controller cannot support. A setting cannot repair a failed component or add an unsupported control interface. The finding should justify the proposed repair or replacement; it should not be inferred from an uncomfortable room or a different thermometer reading alone.
Before any replacement, confirm that the proposed controller supports the existing equipment and required functions. Our Nest and FCU compatibility guide explains the checks for that particular change. If the temperature reading is sound but the equipment ignores commands, use the relevant fan-response or continued-cooling investigation rather than changing calibration to compensate.
Have the authorised service team handle installer settings and agree any landlord or building-control permission first. A lock or schedule needs a permission and control review, not an attempt to bypass it with a new thermostat. Keep the before-and-after settings and retest result, including anything still unresolved. Avoid factory resets, trial wiring changes or moving sensors yourself.
Ask for a clear finding and next step
The visit report should identify the controller, active sensing source, comparison conditions, measured difference and any adjustment or repair. Ask what was checked afterwards and whether another observation is still needed.
If the reading is credible but the room remains warm, our guide to an FCU fan running without cooling explains the separate equipment checks. If you are considering a Nest replacement, review our Nest thermostat and FCU compatibility guide before choosing a controller.
Send DENAIR a display photo, available model details and your temperature record to discuss AC repair and diagnostics. Explain when the mismatch occurs and whether comfort changes with it, so the visit can focus on the right checks.
Explore the relevant scope
Share the equipment, the rooms affected, previous work and available access. DENAIR can assess the relevant scope.
HVAC repair, maintenance, installation and fresh-air work for Dubai properties.
DENAIR is operated by BAFOEV TECHNICAL SERVICES L.L.C. Dubai DET License No. 1118204.