DENAIR

Linear AC Diffusers: Active Length, Plenum and Ceiling Design

Owner review of linear diffuser selection before fabrication

Linear AC Diffusers: Active Length, Plenum and Ceiling Design

Linear AC Diffusers: Active Length, Plenum and Ceiling Design

Linear AC Diffusers: Active Length, Plenum and Ceiling Design

A long ceiling slot can contain sections with different jobs. Before approving linear AC grilles, connect the visible design to the active length, plenum and room airflow selection.

A long ceiling slot can contain sections with different jobs. Before approving linear AC grilles, connect the visible design to the active length, plenum and room airflow selection.

A long ceiling slot can contain sections with different jobs. Before approving linear AC grilles, connect the visible design to the active length, plenum and room airflow selection.

By Denis Perevoshchikov

HVAC Engineer · Certified HVAC Specialist · Manager at DENAIR, Dubai

Fabricated ductwork sections arranged on a worktable

Ductwork sections prepared during a DENAIR project. This photograph shows fabrication context, not a selected linear diffuser assembly.

Which part of a long slot actually supplies air?

A continuous line in a ceiling can include active supply sections, return or extract sections, and closed decorative sections. Before approving the appearance, ask the designer to mark those functions on the ceiling drawing. The visible length alone does not tell you how much air the room receives.

For example, TROX's PURELINE18 documentation includes blind rails with a closed back and describes covered ends where the diffuser face extends beyond its plenum. These are documented product arrangements, not necessarily defects. They show why the active sections and connections need identifying before anyone judges a long grille by touch.

If one end of an existing slot feels different, have the technician compare the installed arrangement with its drawing and model. Do not remove backing, open a decorative section or alter concealed connections to make the whole line blow air.

Select the diffuser and the box behind it together

The plenum is the chamber between the connected duct and the diffuser. Its shape, length and inlet arrangement belong in the selection, alongside the visible face. A neat slot on an interior drawing leaves these details unresolved.

Halton's PLD documentation explains how its plenum reduces incoming air velocity and distributes air through the matched diffuser. Its standard arrangements also vary the number of duct connections with active length. That does not provide a universal rule for other products, but it shows why one connection cannot simply be assumed adequate for every longer outlet.

Ask for a coordinated section showing the selected box, inlet size and position, connecting duct, supports and finished ceiling. If a beam or light fitting forces the box to become shallower or moves the inlet, have the selection reviewed before fabrication. Keep the revised detail with the ceiling drawing so the installer and interior contractor are working from the same arrangement.

Read the performance selection, not just the slot dimensions

A useful proposal connects each room's required airflow to a named diffuser and plenum arrangement. It should explain the intended discharge direction, pressure requirement, sound performance and throw. Throw describes how far the discharged air travels to a specified air-speed limit under the stated test conditions.

The Titus TBD-30 performance tables illustrate the relationship: they list airflow, pressure, noise criteria and throw for particular slot widths, lengths and inlet sizes. Their throw notes specify isothermal test conditions and a one-way pattern, with separate guidance when airflow is divided between directions. Titus also notes that field performance with a flexible-duct inlet can differ.

Ask the designer how the selected data applies to the actual room and cooling operation. A catalogue noise criterion is not a measured sound level in your bedroom, and a throw figure needs its stated conditions. A different-looking substitute should receive its own selection review rather than being accepted solely because it fits the same opening.

Keep the ceiling detail serviceable

Agree how the technical team will reach any balancing device and remove the components intended for servicing. Halton describes a detachable face giving access to its measurement and adjustment module; that feature cannot be assumed for every concealed assembly. Check the ordered variant before the finishing contractor closes around it.

Where the available space is uncertain, our ceiling-space survey guide covers the wider route and equipment constraints. Keep the diffuser decision focused on the selected assembly and the room it serves.

What should remain on the final drawing?

Retain the active and closed lengths, supply or extract function, model and plenum detail, intended airflow and discharge direction. Record approved substitutions. This gives the commissioning team something specific to compare with the installed outlet.

Once the final grilles and connected ducts are fitted, request the relevant airflow results against the agreed design. Our air-balancing report guide explains how to read those measurements. A visually continuous slot and a measured room result answer different parts of the handover.

Planning linear grilles for a Dubai renovation? Share your ceiling layout and room plans with DENAIR to discuss HVAC fit-out and renovation. Discuss the grille and duct arrangement.

Explore the relevant scope

Bring the right details to your enquiry

Bring the right details to your enquiry

Bring the right details to your enquiry

Share the equipment, the rooms affected, previous work and available access. DENAIR can assess the relevant scope.

DENAIR

HVAC repair, maintenance, installation and fresh-air work for Dubai properties.

DENAIR is operated by BAFOEV TECHNICAL SERVICES L.L.C. Dubai DET License No. 1118204.