DENAIR

Why Does an FCU Blow Cold Air in Heating Mode?

Thermostat modes and chilled-water operation

Why Does an FCU Blow Cold Air in Heating Mode?

Why Does an FCU Blow Cold Air in Heating Mode?

Why Does an FCU Blow Cold Air in Heating Mode?

If a chilled-water FCU makes the room colder with Heating selected, check the available heating source, controller sequence and valve response. The mode label alone cannot explain what the equipment is doing.

If a chilled-water FCU makes the room colder with Heating selected, check the available heating source, controller sequence and valve response. The mode label alone cannot explain what the equipment is doing.

If a chilled-water FCU makes the room colder with Heating selected, check the available heating source, controller sequence and valve response. The mode label alone cannot explain what the equipment is doing.

By Denis Perevoshchikov

HVAC Engineer · Certified HVAC Specialist · Manager at DENAIR, Dubai


Wall-mounted thermostat and handheld infrared thermometer during an AC inspection

Controller inspection during a DENAIR service visit. The infrared thermometer measures a surface, not room-air temperature.

Why a Heating label may not mean warm air

On a water-fed fan-coil unit (FCU), the controller requests an operating response. Selecting Heating does not create a hot-water supply. If the room becomes colder after that selection, the technician needs to establish what the controller is asking for, which valve responds and what water is actually available.

A mismatch between the selected sequence and the connected water circuit is one possibility. If a heating request opens a valve supplied with chilled water, the coil may continue cooling rather than warm the room. This is a conditional explanation to investigate, not normal Heating behaviour to assume for every FCU.

This guide concerns water-fed FCUs. A refrigerant-based heat pump or split AC needs its own model-specific investigation. Do not repeatedly switch modes to try to reproduce the problem.

Confirm whether the installed system provides heating

Ask the building or service team whether the room unit has cooling only, a water circuit that changes between heating and cooling, separate heating and cooling circuits, or an additional heater. A Heating option on a display does not identify the equipment connected behind it.

For example, Siemens' RDF4-family two-pipe documentation describes a valve used with heating-only, cooling-only or changeover control. Its four-pipe documentation describes separate heating and cooling valves. Those examples show why the technician must identify the actual arrangement before interpreting a mode symbol.

Check how heating and cooling are selected

Mode selection can depend on more than the wall buttons. For applicable RDF4-family models, Siemens documents different changeover arrangements, including water-temperature sensing, an external switch, building-network information and manual selection. Their availability depends on the model and configuration.

Ask which method your system uses and whether it agrees with the current building supply. If the problem began after a controller replacement or controls work, include that history. Have the technician compare the commissioned sequence with the installed equipment; changing a hidden setting without that check can leave the real mismatch unresolved.

Separate the screen, the valve and the room response

A useful service report should answer these questions for the affected unit:

  • What was selected? Record the displayed mode, requested temperature, measured room temperature and time. Identify the active room sensor if the reading seems doubtful.

  • What should happen? Identify the heating source, if one exists, and the intended fan and valve response for that mode.

  • What actually happened? Establish whether the control command, actuator movement and water-side result agree with that intended response. An actuator indicator alone does not establish flow through the coil.

  • What changed in the room? Compare the temperature trend with the test conditions and note other cooling units or air sources that remained active.

These questions help distinguish a mode or changeover problem from a valve that continues passing water, a separate control fault or a misleading temperature reading. They are checks for the technical team, not a diagnosis from the display alone.

If cooling also continues with Off selected, our FCU switch-off guide covers that separate symptom. If the displayed temperature seems wrong, use the temperature-reading guide before assuming the room has reached the requested setting.

Agree a safe operating plan and a retest

Ask the responsible service or building team which normal user setting to use while the fault is investigated. Leave installer menus, electrical tests, valve handling and ceiling access to authorised technicians. Do not force a valve or remove an actuator to stop cooling.

After any approved correction, request a repeat check of the intended modes with the relevant water supply available. The report should identify the finding, the change made, the demonstrated response and anything still waiting for building access or supply confirmation.

Send DENAIR a display photo, the time of the complaint and any equipment details you already have to arrange AC repair and diagnostics. Explain whether the room becomes colder only in Heating mode or also in other settings.

Explore the relevant scope

Bring the right details to your enquiry

Bring the right details to your enquiry

Bring the right details to your enquiry

Share the equipment, the rooms affected, previous work and available access. DENAIR can assess the relevant scope.

DENAIR

HVAC repair, maintenance, installation and fresh-air work for Dubai properties.

DENAIR is operated by BAFOEV TECHNICAL SERVICES L.L.C. Dubai DET License No. 1118204.